The Knife Blog

How to Keep Restaurant Knives Sharp (Your Dish Machine Is Not Helping)

Your knives got sharpened. Four days later, they're bruising tomatoes again. It's not bad luck. It's your kitchen, and most of it is fixable.

A home cook's knife lives a quiet life. It cuts an onion on Tuesday, gets washed by hand and goes back in the block. A restaurant knife works a double, gets thrown in a bus tub with forty pounds of steel, rides through the dish machine and sleeps in a drawer next to a can opener.

Then everyone acts surprised when the chef's knife can't get through a tomato by Thursday.

Here's the thing: most of the dulling in a restaurant kitchen doesn't come from cutting food. It comes from everything that happens to the knife between cuts. Let's go through the suspects, one at a time.

Why restaurant knives go dull so fast

First, a quick look at what "sharp" is. The edge of a knife is a strip of metal so thin you can't really see it. It's like a row of tiny soldiers standing shoulder to shoulder.

Every time that edge hits something hard, a few soldiers fall over. Hit something hard enough, often enough, and they stop falling over and start leaving.

Food is soft. Your kitchen is not. Here are the five things that knock the soldiers down the most.

1. The dish machine

The dish machine is the best employee you have. It never calls in sick. It also hates knives.

Inside, a knife gets blasted with hot water and strong detergent while it rattles against sheet pans, hotel pans and silverware. The edge bangs into steel over and over. The heat and chemicals are hard on handles too.

It's just a rinse! There was a LADLE in there, Dana. DISH MACHINE hot · loud · no mercy
Ninety seconds in the dish machine: a spa for plates, a mosh pit for edges.

The fix: wash knives by hand, right away, with soap and a towel. Dry them and put them back. It takes twenty seconds. Ten if you're behind.

2. The wrong surface (glass, steel, stone, plates)

A cutting board should be softer than the knife. Plastic and wood are. A stainless prep table, a sheet pan, a glass board or a plate are not.

Cut on those, and the edge hits a surface harder than itself on every single stroke. We asked the edge how it feels about that.

THE EDGE REVIEWS: Cutting Surfaces Plastic board "Soft. Kind. Smellslike onions." Wood board "Like a hugfrom a tree." Steel prep table "Like getting draggeddown I-35." Glass board "Who invented this.Why." A dinner plate "A server did this at 9:45.I remember his face."
The edge has opinions. They are all about your prep table.

The fix: cut on plastic or wood boards. Every time. Even for "just one lime." The lime does not deserve special treatment.

3. Scraping the board with the edge

You know the move. Dice an onion, turn the knife sideways and sweep the pile off the board with the sharp side.

Every cook does it. And every time, the edge drags sideways across the board, which bends it over. Do it a few hundred times a shift and the knife feels dull by lunch.

Every. Single. Onion. Seven years up here. Nobody ever asks ME to scrape. edge (busy) spine (available)
Flip it over. The spine has been waiting its whole career for this.

The fix: flip the knife over and scrape with the spine, the dull back of the blade. Or use a bench scraper. Same pile, same speed, no damage.

The edge is for cutting. The spine is for scraping. The spine is thrilled.

4. Storage: the drawer and the bain-marie

Every kitchen has the drawer. Knives, a can opener, three thermometers, a dead pen and somebody's car key, all sliding around together every time it opens.

Every one of those things is bumping into an edge. Same story with the bain-marie of knives standing tip-down on the line. Every time a knife drops in, the tip lands on the bottom of a steel insert.

The fix: store knives so the edges don't touch anything. A magnetic strip, a knife block, a knife roll or blade guards all work. If knives have to live in a drawer, give each one a guard.

5. The wrong knife for the job

A chef's knife is a cutting tool. It is not a bone saw, a can opener, a box cutter, a pry bar or a way to split a frozen block of chicken thighs.

Twisting through a bone or hacking at frozen food can chip an edge in one move. Opening a case of to-go cups with the 10-inch chef's knife works great right up until it doesn't.

The fix: keep a cleaver for bones, a box cutter for boxes, and a cheap utility knife for the jobs nobody wants to admit they do with a chef's knife. For what each job actually needs, see our list of the best knives for a restaurant kitchen.

How to use a honing steel (and what it can't do)

Here's the good news. A lot of "dull" is really just bent. The soldiers fell over, but they're still there.

That's what a honing steel is for. It pushes a bent edge back into line. It takes off very little metal, so you can do it often. Here's the short version:

  1. Stand the steel straight up, tip on a towel on the board.
  2. Hold the knife at a small angle, about 15 to 20 degrees off the steel.
  3. Pull it down the steel, heel to tip, with light pressure.
  4. Switch sides. Four to six light strokes per side is plenty.

Do it at the start of a shift, and again whenever the knife starts to drag. Light and slow beats hard and loud. (The full walkthrough, with pictures, is in how to hone a knife.)

Now the bad news. Honing can only straighten metal that's still there. Once the edge is worn round, there's nothing left to line up.

Forty more strokes. Dana. I'm not bent. I'm ROUND. ...212 ...213 ...214
A steel straightens a bent edge. It can't bring back one that's gone. Dana is still trying.

When it's time to sharpen restaurant knives for real

Honing buys time. It doesn't buy forever. Here's how to tell the steel has done all it can:

When you hit those signs, the knife needs a new edge ground on it. That's sharpening. A busy line usually needs it a lot more often than people think. (Here's how often a restaurant should sharpen its knives.)

Good habits make a sharp edge last longer. They can't make it last forever.

How to sharpen restaurant knives without thinking about it

You can buy stones and have someone on staff learn to use them. Some kitchens do. Most find out that the person who's good at it is also the person with no time.

The other way is to put your kitchen on a route. That's what we do. On the same day every week, the same driver parks at your back door and sharpens your knives right on the truck. They're back inside in minutes. Kitchens that can't spare a knife at all can use knife swap, where a sharp set comes in as the dull set goes out.

Restaurant routes start at $45 a visit for 10 knives, plus a $5 fuel charge. Prices are posted, not hidden behind a sales call:

New-customer route prices, per visit. Knife swap and multi-location groups are quoted.

We've sharpened for kitchens across Dallas, Fort Worth and Austin since 2008. Gloves, liners, film and other supplies can come on the same stop. And if a knife comes back not right, we re-do it.

Want your knives sharp every week? Leave your name and number on the restaurant call-me form and we'll call you with your route day and price. Or call or text (214) 701-5564. Everything we do for kitchens is on our restaurant knife sharpening page.

(Heads up: Thanksgiving week, November 23–27, we're open Monday through Wednesday only.)

Questions chefs ask

How do I keep restaurant knives sharp longer?
Keep them out of the dish machine, cut only on plastic or wood boards, scrape the board with the spine instead of the edge, store them so the edges don't touch anything, and hone them lightly at the start of every shift.
Why do restaurant knives get dull so fast?
Mostly because of what happens between cuts: the dish machine, cutting on steel tables or plates, scraping the board with the edge, loose drawer storage and using a chef's knife for bones, frozen food or boxes.
Does a honing steel sharpen a knife?
No. A honing steel pushes a bent edge back into line and takes off very little metal. Once the edge is worn round or chipped, the knife needs real sharpening. See how to hone a knife.
How often should cooks hone their knives?
A few light strokes per side at the start of each shift, and again whenever the knife starts to drag. If honing stops helping, it's time to sharpen.
Can restaurant knives go in the dishwasher?
They shouldn't. The heat, detergent and knocking against pans dull the edge and are hard on handles. Wash knives by hand, dry them and put them away.
How much does it cost to sharpen restaurant knives?
Our restaurant routes start at $45 a visit for 10 knives, plus a $5 fuel charge, with the same driver sharpening on the truck at your back door every week. Fill out the call-me form for your route day.

Restaurants: get startedHome cooks: book sharpening

More from the Knife Blog

All posts →

Ready for sharp knives?

Call or text (214) 701-5564, or start online in two minutes.

Restaurants Home cooks

CallRestaurantsHome cooks